TSX:MNB, ASX:MBN
Ordinary shares outstanding: 129,784,100
PERTH, Australia, Sept. 4 /CNW/ - Mirabela Nickel Limited (ASX:MBN, TSX MNB) is pleased to announce an upgraded in-pit resource for the Santa Rita project comprising:
- 130 million tonnes at 0.60% Ni & 0.16% Cu (Measured and Indicated)
for 780,000t of contained Ni
- 20 million tonnes at 0.60% Ni & 0.16% Cu (Inferred) for an additional
120,000t of contained Ni
- Indicative strip ratio 7.6 to 1
This represents a 45% increase in the Measured and Indicated nickel resource compared with the previous November 2007 resource estimate. At a planned throughput rate of 6.4 mtpa, to produce 27,000tpa of nickel, this resource represents over 20 years of mine life.
"This resource increase substantially exceeds expectations and affirms Santa Rita as a world class nickel discovery." said Managing Director, Nick Poll. "The Southern deeps high-grade zone made a large contribution to the new open-pit resource despite being discovered less than 6 months ago and it remains open at depth. We are seeing consistent improvement in both width and grade around the base of the open-pit resource right across the entire 2km of strike length. There is potential for yet another good open-pit resource upgrade, mainly in the Central zone, and there is very large underground resource potential."
The additional 20 million tonnes of Inferred resource lies at the base of the open pit. If fully converted to Indicated status this would add another 120,000t of Ni to the open-pit resource. As a result, the Company is now targeting an open-pit Indicated resource between 900,000t and 1,000,000t of contained Ni. This target is well within reach, due to the continuity of the ore body and the improvement of width and grade with depth seen in drilling over the last 6 months.
"Over 900,000t of contained nickel would make Santa Rita larger than the current Voisey's Bay open-cut project and about 80% the size of the current Mt Keith nickel project. These are the two largest open-cut nickel sulphide projects in the world. Even including underground operations, there are only a handful of nickel sulphide projects in the world of this size," said Mr Poll.
In addition to this open-pit resource, the Company is currently drilling up an extensive underground resource below the Southern deeps high-grade zone. An Inferred underground resource is due to be completed by November with only 2 holes of the initial program remaining to be drilled. The Company is studying the potential for this underground resource to drive further increases in the size of the Santa Rita project.
Following are additional details on the resource estimate.
Primary In-pit Resource
The updated Potential Mill Feed Resource (the estimated resource available as mill feed based upon a pit optimisation study) is:
Potential Mill Feed Estimate
(Indicative strip ratio 7.6:1)
-------------------------------------------------------------------------
Million Pt Tonnes Million
Category Tonnes Ni Cu Co (g/t) Ni lbs Ni
-------------------------------------------------------------------------
Measured 15.1 0.65% 0.16% 0.017% 0.108 98,000 220
-------------------------------------------------------------------------
Indicated 115.2 0.60% 0.16% 0.015% 0.092 691,000 1,520
-------------------------------------------------------------------------
Measured
+ Indicated 130.3 0.60% 0.16% 0.016% 0.094 789,000 1,740
-------------------------------------------------------------------------
Inferred 19.8 0.60% 0.16% 0.016% 0.086 119,000 265
-------------------------------------------------------------------------
Includes 5% ore loss. Weighted average cut-off grade - 0.34% Ni.
See Attachment 2 below.
The new Measured and Indicated resource (130.3mt grading 0.60% Ni) represents an increase of 45% above the open-pit resource announced in November 2007 (90.0mt grading 0.61% Ni) and 88% over the open-pit resource announced in June 2007 (69.2mt grading 0.61%). This substantial increase exceeds expectations and reflects excellent drilling results extending and widening the resource in the southern half.
The maximum depth of the open-pit resource is now 640m, compared with 500m for the previous estimate. The strip ratio remains at 7.6 to 1, due to the wider mineralization at depth and good geotechnical results that allowed steepening of the pit walls. The average cut-off grade is lowered to 0.34% Ni from 0.36% Ni as part of the optimisation process.
This resource estimate has been independently reviewed by Coffey Mining Pty Ltd in accordance with the Australian JORC and the Canadian NI 43.101 reporting guidelines. For technical details in relation to the calculation of the resources see Attachment 1.
Pit optimisation studies for the Santa Rita resource were undertaken by independent consultant Croeser Pty Ltd using the following parameters:
- The operating costs from the pit optimisation study announced
November 2007 increased by 10% (representing a 10% reduction in the
long term exchange rate to US$:1.80 Real)
- Latest pit slopes as recommended by Brazil-based geotechnical
consultants VOGBR
- A nickel price of US$7.00/lb (the same as used in the previous
resource estimate)
Work is underway to calculate a Proven and Probable Reserve based upon the Measured and Indicated resource, expected to be announced in October.
Low Grade Resource
In addition to the Primary In-pit resource (average cut-off 0.34% Ni) there is a halo of lower grade mineralisation (average cut-off 0.25% Ni) within the same pit shell. This lower grade mineralisation is free at surface as it is mined as waste when the Primary In-pit resource is mined.
Low Grade Resource - Potential Mill Feed Estimate
(within same pit as Primary Resource)
-------------------------------------------------------------------------
Million Pt Tonnes Million
Category Tonnes Ni Cu Co (g/t) Ni lbs Ni
-------------------------------------------------------------------------
Measured
+ Indicated 47.0 0.30% 0.07% 0.012% 0.072 141,000 311
-------------------------------------------------------------------------
Inferred 6.0 0.30% 0.07% 0.012% 0.071 18,000 40
-------------------------------------------------------------------------
Includes 5% ore loss. Weighted average lower cut-off grade
0.25% Ni and upper cut-off grade 0.34% Ni. See Attachment 2 below.
Without any mining cost, this Low Grade resource is cashflow positive through the Mill. However, to maximise the net present value of the project this mineralisation needs to be processed at the end of the project rather than displacing the higher cashflows generated by the Primary In-pit resource in earlier periods. Accordingly, the Low Grade resource will be stockpiled and treated at the end of the project after all Primary In-pit resource is exhausted. This will add significant life to the project, especially if combined with underground resource.
Drilling To Date The following table summarizes the diamond drilling at Santa Rita completed to date: ------------------------------------------------------------------------- Santa Rita resource Drill holes Approx meters drilled ------------------------------------------------------------------------- Oct 2006 resource estimate 244 56,000 June 2007 resource estimate 313 73,500 Nov 2007 resource estimate 378 93,750 Latest Sept 2008 resource estimate 538 139,450 Total resource drilling to date 556 156,100 -------------------------------------------------------------------------
The new resource is based on 538 drill holes compared with 378 holes for the previous mineral resource. A further 18 holes have been drilled since commencement of the resource estimate, but assays were pending at the cut-off date.
Updated Santa Rita Resource Targets
The favourable drilling results have led to a revision in the target size of the Santa Rita project. The Company's ongoing drilling programs are now targeting:
-------------------------------------------------------------------------
Current Current
Indicated Inferred Target Target
Santa Rita Grade (mt) (mt) (mt) (Ni tonnes)
-------------------------------------------------------------------------
Open-pit Resource 0.60% 130 20 150 - 900,000
170 - 1,020,000
Underground
Resource 0.80% nil nil 50 - 400,000
150 - 1,200,000
Total 200 - 1,300,000
320 - 2,220,000
Plus Low Grade
Resource 0.30% 47 6 50 -
60
-------------------------------------------------------------------------
Santa Rita will almost certainly become a "Million Tonne Monster" following the announcement of the maiden underground resource, expected by November this year. The underground drilling is progressing well, with 15 holes drilled and only 2 holes to be completed in the current program, and excellent results to date. The total underground potential is exceptionally large and drilling to date has only covered a portion of the prospective area.
The Company is now pursuing a "40,000 for 25" objective - a production rate of over 40,000tpa Ni in concentrate with a mine life of at least 25 years. The concept is to increase the plant throughput to 9 mtpa fed contemporaneously by about 6 mtpa from the open-pit and 3 mtpa from underground. A life of 25 years would require 150mt of open-pit resource and 75mt of underground resource.
The Company has commenced feasibility work on the potential underground resource. Early cashflow from the open-pit could be used to fund the underground development costs and associated plant throughput increase. The Santa Rita plant has been designed to enable a potential throughput increase. It will take about two years to access underground positions with a decline. Subject to feasibility results, commencement of decline development could begin early next year.
A combination of the low grade stockpile and more underground resource could add a further 10 year tail to the project, albeit at a lower nickel production rate, for a total potential life of over 35 years. Although not fully recognised in a simple discounted cash flow calculation, long life, low cost, nickel sulphide assets are rare and strategically valued in an industry where the prize assets are tightly held. This is particularly so given recently revealed high costs and risks of nickel laterite projects. Mirabela is committed to proving up a long life project and drilling will continue with 5 rigs active.
Project Construction Update
Construction of the project is now about 60% complete and the project remains on target for commencement of production in mid 2009. Construction works on all the major plant components are well advanced.
Infrastructure for the crusher and its electrical substation will be ready to receive the crusher later this month. Foundations have been completed for the grinding circuits, flotation circuits and thickeners. The sag mill, ball mill and flotation cells are all on schedule for delivery in December and construction of the thickeners has commenced.
Construction of the tailings dam, access roads and bridges, maintenance and administration buildings, and water facilities are all well advanced. About 3.7mt of pre-strip material has been removed from the open pit, the orebody is exposed, and mining of ore will shortly commence.
Nick Poll Craig Burton Managing Director Corporate Director Background
Mirabela Nickel Ltd is listed on the Australian and Toronto stock exchanges. With an open-pit indicated resource of 130mt grading 0.60% Ni, Santa Rita is the largest greenfields nickel sulphide discovery in the last 12 years world-wide.
Construction of a nickel sulphide concentrator commenced in November 2007 and is progressing well. The plant is expected to produce 18,500 tpa of nickel in a sulphide concentrate from one open-cut mine starting from mid 2009 increasing to 27,000 tpa by mid 2010. At this rate of production the project will have a mine life of at least 20 years.
The information in this report that relates to Mineral Resources and Exploration Results is based on information compiled by Lauritz Barnes who is a Member of The Australian Institute of Geoscientists, and Brett Gossage, who is a Member of The Australasia Institute of Mining and Metallurgy. Lauritz Barnes is consultant to Mirabela Nickel Limited. Brett Gossage is the Senior Principal with Coffey Mining Pty Ltd, independent resource consultants engaged by Mirabela Nickel Limited.
Lauritz Barnes and Brett Gossage have sufficient experience which is relevant to the style of mineralization and type of deposit under consideration and to the activity which he is undertaking to qualify as a Competent Person as defined in the 2004 Edition of the 'Australasian Code for Reporting of Exploration Results, Mineral Resources and Ore Reserve' and are each a Qualified Person in accordance with NI 43-101. Lauritz Barnes and Brett Gossage consent to the inclusion in the report of the matters based on their information in the form and context in which it appears.
The information in this report that relates to pit optimization and scheduling studies is based on information compiled by Roselt Croeser who is a Member of The Australasia Institute of Mining and Metallurgy. Roselt Croeser is a consultant to Mirabela Nickel Limited. Roselt Croeser consents to the inclusion in the report of the matters based on his information in the form and context in which it appears.
All other technical information in this report has been reviewed by Nicholas Poll, who is a Member of The Australasia Institute of Mining and Metallurgy. Nicholas Poll is the Managing Director of the Company. Nicholas Poll consents to the inclusion in the report of the matters based on his information in the form and context in which it appears.
Caution Regarding Inferred Resources: Inferred resources are, by definition, of insufficient confidence to have economic considerations applied that would enable them to be categorised as mineral reserves, and there is no certainty that any preliminary assessment will be realised in respect of such resources. In the present case, the Inferred resources comprise about 13% of the total resource estimate.
Caution Regarding Forward Looking Statements: The forward-looking statements made in this announcement are based on assumptions and judgments of management regarding future events and results. Such forward-looking statements, including but not limited to those with respect to resource targets or the development of an underground mine at Santa Rita and the Company's estimated future production involve known and unknown risks, uncertainties, and other factors which may cause the actual results, performance or achievements of the Company to be materially different from any anticipated future results, performance or achievements expressed or implied by such forward-looking statements. Such factors include, among others, the actual market prices of nickel, the actual results of current exploration, the actual results of future mining, processing and development activities, changes in project parameters as plans continue to be evaluated, as well as those factors disclosed in the Company's filed documents.
www.mirabela.com.au
-------------------
Attachment 1: Technical background on resource estimate
The resource has been classified in accordance with Canadian Institute of Mining, Metallurgy and Petroleum (CIM) guidelines and with reference to the criteria set out in the Australasian Code for Reporting of Exploration Results, Mineral Resources and Ore Reserves (JORC Code, December 2004). The estimation has been carried out by a Competent Person from the Company and a Competent Person from Coffey Mining Pty Ltd in accordance with the Code and as such is suitable for inclusion in a public report.
In total, the grade interpolation dataset used for the resource estimate consisted of 538 diamond holes. All drill core has been logged in detail for lithological and structural information. Nickel and multi-element assaying has been completed on half core samples using inductively coupled plasma atomic emission spectroscopy (ICP-AES) and inductively coupled plasma mass spectroscopy (ICP-MS) methods with appropriate collectors (for example 30g fire assay for Pd, Pt and Au). All assaying is accompanied by rigorous submission and analysis of QAQC samples. An extensive specific gravity database has been collected by weighing of diamond core in air and water.
The resource model was derived via geological and mineralisation zone modelling of the deposit. Estimation involved the application of Ordinary Kriging in panels of 20m E-W by 25m N-S by 5mRL for Ni, Cu, Co, Pd, Pt, Au, Fe, Mg and S with Uniform Conditioning change of support for Ni only for a base case selective mining unit of 5mE by 10mN by 5mRL. Technique selection was based on the quantity and spacing of available data, and the interpreted controls on, and styles of, mineralisation under review.
Attachment 2: Details on cut-off grades used
A variety of cut off grades are required for each ore type, because they vary in olivine content. Olivine contains non-sulphide nickel that is not recoverable (silicate nickel), so lower olivine content increases nickel recovery and reduces the corresponding cut-off grade. Mineral resource grades reflect the combined sulphide and silicate nickel content, because assay technology is not accurate enough to measure sulphide nickel content alone for mineral resource estimation.
There are four different types of mineralised rock. Each has a different cut-off grade depending on its non-sulphide nickel content. Pyroxenite has a low cut-off grade to reflect low olivine and low non-sulphide nickel content, whereas dunite has a high cut-off grade to reflect high olivine and high non-sulphide nickel content. The table below provides a breakdown of the resource rock types, their associated cut-off grades and a comparison with the previous (November 2007) estimate.
Comparison of cut-off grades between new and previous
potential mill feed tonnages
-------------------------------------------------------------------------
September 2008 estimate November 2007 estimate
----------------------------------------------------
Host rock type Percentage Cut-off Percentage Cut-off
composition Grade composition grade
-------------------------------------------------------------------------
Pyroxenite 62 0.30% 58 0.32%
Olivine
Orthopyroxenite 14 0.35% 14 0.35%
Harzburgite 21 0.45% 25 0.45%
Dunite 3 0.50% 3 0.50%
Weighted average
cut-off grade 100% 0.34% 100% 0.36%
-------------------------------------------------------------------------
In addition, a lower resource cut-off grade has been used as set out
below:
Details for lower cut-off grade
-------------------------------------------------------------------------
Lower cut-off grade resource
-------------------------------
Host rock type Percentage Cut-off
Composition grade
-------------------------------------------------------------------------
Pyroxenite 61 0.20%
Olivine Orthopyroxenite 14 0.25%
Harzburgite 22 0.35%
Dunite 3 0.40%
Weighted average cut-off grade 100% 0.25%
-------------------------------------------------------------------------