PERTH, Western Australia, Nov. 28 /CNW/ - Mirabela Nickel Limited ("Mirabela") (TSX: MNB, ASX: MBN). This announcement is to clarify recently announced resource targets at Santa Rita as follows:
-------------------------------------------------------------------------
Santa Rita Grade Current Target Target
(mt) (mt) (Ni tonnes)
-------------------------------------------------------------------------
Primary Resource
(In-pit) 0.60% 90 120 - 130 720,000 - 780,000
Secondary Resource
(In-pit) 0.31% 38 45 - 50 140,000 - 155,000
Underground Resource 0.75% nil 20 - 40 150,000 - 300,000
-------------------------------------------------------------------------
Total 0.55% 128 185 - 220 1,010,000 - 1,235,000
-------------------------------------------------------------------------
(x) The above resource targets are conceptual in nature, there has been
insufficient exploration to define a Mineral Resource in the target
quantities and grades and it is uncertain if further exploration will
result in the determination of such Mineral Resources.
The current in-pit Primary Resource is 90mt at 0.60% Ni Indicated and 10.7mt at 0.60% Ni Inferred. The target Primary Resource contemplates conversion of the current Inferred resource to Indicated and a further 20% to 30% increase in the in-pit resource through additional drilling.
The Company is aiming to achieve this through deeper drilling across the whole Southern zone and by drilling up the new South-East Extension area. Since the cut-off date for the last resource calculation a further 44 holes have been drilled in these areas, most with assays pending. Excellent results were recently announced in the South-East Extension area, none of which was available in time for inclusion in the last resource calculation.
The Secondary Resource is a lower grade halo around the Primary Resource and is expected to increase roughly in proportion to any increase in the Primary Resource.
The underground resource target is very much a conceptual target. A recently discovered zone of mineralisation known as the southern high grade zone has good continuity below 200m vertical depth and along 240m of strike averaging 88m true width and 0.79% Ni. This mineralisation remains open at depth. There is also underground resource potential beneath a central high grade zone where about 140m of strike averages 42m true width and 0.77% Ni.
The target underground resource contemplates possible continuity of these zones at similar widths and grades for a further 300m to 500m below the pit limits. The Company is commencing a new drilling program to test these deeper zones.
Nick Poll Craig Burton Managing Director Corporate Director
All technical information in this report has been reviewed by Nicholas Poll, who is a Member of The Australasia Institute of Mining and Metallurgy. Nicholas Poll is the Managing Director of the Company. Nicholas Poll consents to the inclusion in the report of the matters based on his information in the form and context in which it appears.
Caution Regarding Forward Looking Statements: The forward-looking statements made in this announcement are based on assumptions and judgments of management regarding future events and results. Such forward-looking statements involve known and unknown risks, uncertainties, and other factors which may cause the actual results, performance or achievements of the Company to be materially different from any anticipated future results, performance or achievements expressed or implied by such forward-looking statements. Such factors include, among others, the actual market prices of nickel, the actual results of current exploration, the actual results of future mining, processing and development activities, changes in project parameters as plans continue to be evaluated, as well as those factors disclosed in the Company's filed documents.
Attachment 1: Technical background on resource estimate
The resource has been classified in accordance with Canadian Institute of Mining, Metallurgy and Petroleum (CIM) guidelines and with reference to the criteria set out in the Australasian Code for Reporting of Exploration Results, Mineral Resources and Ore Reserves (JORC Code, December 2004). The estimation has been carried out by a Competent Person from the Company and a Competent Person from Coffey Mining Pty Ltd in accordance with the Code and as such is suitable for inclusion in a public report.
In total, the grade interpolation dataset used for the resource estimate consisted of 378 diamond holes. All drill core has been logged in detail for lithological and structural information. Nickel and multi-element assaying has been completed on half core samples using inductively coupled plasma atomic emission spectroscopy (ICP-AES) and inductively coupled plasma mass spectroscopy (ICP-MS) methods with appropriate collectors (for example 30g fire assay for Pd, Pt and Au). All assaying is accompanied by rigorous submission and analysis of QAQC samples. An extensive specific gravity database has been collected by weighing of diamond core in air and water.
The resource model was derived via geological and mineralisation zone modelling of the deposit. Estimation involved the application of Ordinary Kriging in panels of 20m E-W by 25m N-S by 5mRL for Ni, Cu, Co, Pd, Pt, Au, Fe, Mg and S with Uniform Conditioning change of support for Ni only for a base case selective mining unit of 5mE by 10mN by 5mRL. Technique selection was based on the quantity and spacing of available data, and the interpreted controls on, and styles of, mineralisation under review.
Attachment 2: Details on cut-off grades used
A variety of cut off grades are required for each ore type, because they vary in olivine content. Olivine contains non-sulphide nickel that is not recoverable (silicate nickel), so lower olivine content increases nickel recovery and reduces the corresponding cut-off grade. Mineral resource grades reflect the combined sulphide and silicate nickel content, because assay technology is not accurate enough to measure sulphide nickel content alone for mineral resource estimation.
There are four different types of mineralised rock. Each has a different cut-off grade depending on its non-sulphide nickel content. Pyroxenite has a low cut-off grade to reflect low olivine and low non-sulphide nickel content, whereas dunite has a high cut-off grade to reflect high olivine and high non-sulphide nickel content. The table below provides a breakdown of the resource rock types, their associated cut-off grades and a comparison with the previous (June 2007) estimate.
Comparison of cut-off grades between new and previous
potential mill feed tonnages
-------------------------------------------------------------------------
November 2007 estimate June 2007 estimate
--------------------------------------------------
Host rock type Percentage Cut-off Percentage Cut-off
composition Grade composition grade
-------------------------------------------------------------------------
Pyroxenite 58 0.32% 41 0.35%
Olivine Orthopyroxenite 14 0.35% 15 0.40%
Harzburgite 25 0.45% 40 0.40%
Dunite 3 0.50% 4 0.50%
Weighted average cut-
off grade 100% 0.36% 100% 0.38%
-------------------------------------------------------------------------
In addition, a lower resource cut-off grade has been used as set out
below:
Details for lower cut-off grade
------------------------------------------------------------------------
Lower cut-off grade resource
-----------------------------
Host rock type Percentage Cut-off
Composition grade
-------------------------------------------------------------------------
Pyroxenite 58 0.22%
Olivine Orthopyroxenite 13 0.25%
Harzburgite 26 0.35%
Dunite 3 0.40%
Weighted average cut-off grade 100% 0.26%
-------------------------------------------------------------------------