Slide 1: SikaQuick 1000 Application Instructions
Construction SikaQuick 1000 Application Instructions Sika Corporation
Slide 2: Rapid Hardening Repair Mortar with Extended Working Time
Construction SikaQuick 1000 Rapid Hardening Repair Mortar with Extended Working Time. Sika Quick is a 1-component ,rapid hardening, early strength gaining cementitous based material for patching concrete. Sika Corporation
Slide 3: Where to use
Construction SikaQuick 1000 S Where to use: S Use on grade, above and below grade on concrete. S Highway overlays and repairs. S Structural Repair material for concrete roadways, parking structures, bridges, dams and ramps. S Full depth patching. S Economical patching material for horizontal repairs
Slide 4: Coverage
Construction SikaQuick 1000 Coverage: S SikaQuick 1000 Mortar Approximately 0.43 cu.ft S SikaQuick 1000 Concrete When extended with 25 lbs. of 3/8 in gravel approximate yield = 0.6 cu.ft Sika Corporation
Slide 5: Packaging
Construction SikaQuick 1000 S Packaging: 50 lb – Multi wall Bag 40 Bags/Pallet Sika Corporation
Slide 6: Surface Preparation
Construction Surface Preparation Cementitious Substrates: 1. Should be clean and sound. 2. Remove contaminations and bond inhibiting materials from repaired area. 3. Obtain exposed/fractured aggregate surface ~1/8 to 1/4 inch profile (ICRI CSP 6 & above). 4. Substrate must be saturated surface dry (
Slide 7: Surface Preparation
Construction Surface Preparation S Cementitious Substrates: • Surface should be cleaned and roughened to create a profile. Sika Corporation
Slide 8: Surface Preparation
Construction Surface Preparation S Saw cut around perimeter or repair area to achieve a minimum 1/8” shoulder. S This will eliminate feather edging the product and give a clean transition for the repair. Sika Corporation
Slide 9: Surface Preparation: Steel
Construction Surface Preparation S Steel: • Remove all corrosion and contaminants from exposed steel. • Surface should be cleaned thoroughly by blast cleaning or mechanical means. • Exposed steel should be cleaned to white steel. • If half of the diameter is exposed, chip behind bar, ½” minimum for
Slide 10: Steel Preparation
Construction Steel Preparation S Steel should be cleaned to a bright metal finish. Sika Corporation
Slide 11: Tools Required
Construction Tools Required S ½” Drill Motor S Low speed drill 400-600 rpm S Mortar mixer or Jiffy mixer S Margin trowel S Steel/Mag Trowel S Spatula Sika Corporation
Slide 12: Surface Preparation
Construction Surface Preparation S Saw cut around perimeter or repair area to achieve a minimum 3/8” shoulder. This will eliminate feather edging the product and give a clean transition for the repair. Sika Corporation
Slide 13: Surface Preparation: Steel
Construction Surface Preparation S Steel: 1. Remove all corrosion and contaminants from exposed steel. 2. Surface should be cleaned thoroughly by blast cleaning or mechanical means. 3. Exposed steel should be cleaned to white steel. 4. If half of the diameter is exposed, chip behind bar, ½” minimum
Slide 14: Mixing
Construction Mixing Mixing Equipments I. Mortar Mixer II. Drill and Paddle. Wet down tools and equipments before proceeding to mix. Sika Corporation
Slide 15: Mixing - SikaQuick Mortar
Construction Mixing- SikaQuick Mortar 1. Water – 4.5-5 Pts/Bag 2. Latex-R- 4.5-5 Pts/Bag. 3. Start with adding liquid to the mixing container. 4. Slowly add powder. 5. Once all the powder is added mix for 3 minutes. 6. Do not add any more than 5 pts of liquid. water. Sika Corporation
Slide 16: Mixing - SikaQuick Concrete
Construction Mixing- SikaQuick Concrete 1. Water – 4.5-5 Pts/Bag 2. Latex-R- 4.5-5 Pts/Bag. 3. Stone - 3/8 gravel 25#/bag. 4. Stone – Weigh Before SSD. 5. Start with adding liquid to the mixing container. 6. Slowly add powder. 7. Once all the powder is added and mixed add stone. 8. Mix time 3 minute
Slide 17: Aggregate Selection & SSD
Construction Aggregate Selection & SSD S Consult Technical Data Sheets for detailed recommendations on aggregate selection. Sika Corporation
Slide 18: Min / Max application thickness
Construction Min / Max application thickness S Neat • Min 1/4 inch • Max 1 inch S Extended • Min 1 inch • Max 6 inches Sika Corporation
Slide 19: Scrub/Slurry Coat
Construction Scrub/Slurry Coat Sika Corporation
Slide 20: Placement
Construction Placement Sika Corporation
Slide 21: Placement
Construction Placement Sika Corporation
Slide 22: Finishing
Construction Finishing Sika Corporation
Slide 23: SikaTop Curing
Construction SikaTop Curing S Cure as per ACI recommendations. Curing is required. S Moist cure with wet burlap and polyethylene, a fine mist of water. S Moist curing should commence immediately after finishing. S Protect newly applied material from direct sun light, wind, rain and frost. Sika Corpo
Slide 24: Curing
Construction Curing Sika Corporation
Slide 25: SikaQuick 1000 Technical Data Sheets
Construction SikaQuick 1000 Sika Technical Data Sheets can be obtained via: www.sikaconstruction.com Refer to data sheets for specific information on each Sika product. Sika Corporation