Lincoln Educational Services Corporation · NASDAQ:LINC
Lincoln Educational Services — Investor Presentation (July 2024)
14 slides from Lincoln Educational Services's investor presentation, July 2024
Slide 1: Ironworker Operation & Safety
IRONWORKER OPERATION & SAFETY 168690724
Slide 2: Potential Risk
POTENTIAL RISK There a re a number of pa rticula r ha za rds a s s ocia ted with the opera tion a nd us e of ironworkers . Crus hing and Shear Points – Shear point hazard exis ts when the edges of two m a chine pa rts m ove a cros s ea ch other or m ove clos ely enough together to cut a nother objec
Slide 3: Flying and Moving Parts
Flying and Moving Parts Flying or ejected parts from either the stock or the tooling can strike operators and other workers in the area. Furthermore, punches are hardened and will not bend as they collide with dies. If a punch is out of alignment, it is more likely to flake, fracture, or even explod
Slide 4: Avoiding Potential Risk
AVOIDING POTENTIAL RISK • Identify the areas of crushing and shear point hazards • Make sure all guards are in place and in working condition • Wear clothing that fits well because close-fitting clothing is less likely to be pulled into moving parts • Never reach across a shear or cutting point haza
Slide 5: How to Operate the Ironworker - 1
HOW TO OPERATE THE IRONWORKER - 1 • Push to Start – This button energizes the machine. When energized this recessed button is internally illuminated and will glow “green”. If the machine does not start when pressed, an emergency palm stop button may have been previously pressed and will need to be r
Slide 6: How to Operate the Ironworker - 2
HOW TO OPERATE THE IRONWORKER - 2 • Emergency Palm Stop - This button de-energizes the machine and contains a manual, safety reset function. The projecting “red” palm stop style button is set within a safety yellow bezel and is pushed to de-energize the machinery. Once de-energized the machine requi
Slide 7: How to Operate the Ironworker - 3
HOW TO OPERATE THE IRONWORKER - 3 • Operations Control – This three-position switch allows the ironworker operation to shuttle between Ironworker, hydraulic accessory or auto-cut mode. • Ironworker Power – Power on the Ironworker by rotating the three position switch counterclockwise. This function
Slide 8: How to Operate the Ironworker - 4
HOW TO OPERATE THE IRONWORKER - 4 • Lockout/Tagout – This “red” round, safety switch is set within a square safety yellow housing. The switch allows for proper procedures to be followed when de- energizing, isolating, and ensuring the energy isolation of the Ironworker. The Lockout/Tagout switch is
Slide 9: How to Use the Shear on the Ironworker
HOW TO USE THE SHEAR ON THE IRONWORKER 1. Clear bar shear station of any tools or debris prior to powering the machine on. 2. Turn machine on. The shear blades will be in their neutral position. Place bar stock on the feed table and push the material under the material hold-down. Position your desir
Slide 10: While Operating the Shear on the Ironworker
WHILE OPERATING THE SHEAR ON THE IRONWORKER • Never exceed the capacities of the machine or tooling as described in the Ironworker specifications • Check shear blade clearance at every tooling change or extended shear operation Maintain correct operating clearance at bar shear and angle shear statio
Slide 11: Warning Sticker Locations
WARNING STICKER LOCATIONS The next few slides will show you all locations of warning labels on the Edward ironworker. Manufacturers and models vary.
Slide 12: Warning Sticker Locations
Put Your Potential To WARNING STICKER LOCATIONS
Slide 13: Danger Panel
DANGER PANEL WARNING PANEL NGER Electrical Hazard This is the electrical hazard symbol. indicates there are. dangerous nigh valt- {ages present inside the enclosure of tis product. ONLY qualified, aumorzed, main {enancs, service or Cerifled lect Iclans should Gain access to electrical panel. Do not
Slide 14: Metal Pro MP5000FS Ironworker Safety Stickers
Metal Pro MP5000FS Ironworker Safety Stickers
Lincoln Educational Services — Investor Presentation (July 2024) on 6ix