Sika Ag · SIX:SIKA
Sika — Technical Presentation
20 slides from Sika's technical presentation
Slide 1: Sika Armatec 110 Application Instructions
Construction Sika Armatec 110 Application Instructions Sika Corporation
Slide 2: Sika Armatec 110 EpoCem Bonding Agent and Reinforcement Protection
Construction Sika Armatec 110 EpoCem Bonding Agent and Reinforcement Protection Sika Armatec 110 EpoCem is a 3-component, solvent-free, epoxy- modified, cementitious product specifically formulated as a bonding agent and an anti-corrosion coating Sika Corporation
Slide 3: Where to use
Construction Sika Armatec 110 EpoCem S Where to use: S As a anti-corrosion coating for reinforcing steel in concrete restoration S As Added protection to reinforcing steel in areas of thin concrete cover S As a bonding agent for repairs to concrete and steel S As a bonding agent for placing fresh, p
Slide 4: Coverage
Construction Sika Armatec 110 EpoCem S Coverage: Bonding Agent: minimum on smooth, even substrate 80 sq.ft./ gal (@20 mils) Reinforcement Protection: 40 sq.ft./gal (@20 mils – 2 coat application) Sika Corporation
Slide 5: Packaging
Construction Sika Armatec 110 EpoCem S Packaging: 3.5 Gal Unit: “A” Comp: 47.6 fl. Oz. “B” Comp: 122.1 fl. Oz. “C” Comp: multi-wall bag 1.65 Gal Unit: “A” Comp: 22.7 fl. Oz. “B” Comp: 57.6 fl. Oz. “C” Comp: 4 Bags @ 5.5 lbs ea. Sika Corporation
Slide 6: Surface Preparation: Cementitious Substrates
Construction Surface Preparation Cementitious Substrates: Should be cleaned and prepared in accordance with the requirements specified by the overlay or repair material by blast cleaning or equivalent mechanical means. Substrate must be saturated surface dry (SSD) with no standing water. Sika Co
Slide 7: Surface Preparation: Steel
Construction Surface Preparation S Steel: Remove corrosion and contaminants from exposed steel. Surface should be cleaned and prepared thoroughly by blast cleaning. Exposed steel should be cleaned to white steel. Determine section loss, splice where more than 15-25% loss as directed the Engi
Slide 8: Sika Armatec EpoCem 1.65 Gal Unit
Construction SikaArmatec 110 EpoCem 1.65 Gal Unit Comes packaged with 4 bags @ 5.5 lbs. excellent for smaller batches. Sika Corporation
Slide 9: Armatec EpoCem Tools
Construction Armatec 110 EpoCem- Tools 1.65 Gal Unit Comes packaged with 4 bags @ 5.5 lbs. excellent for smaller batches. Sika Corporation
Slide 10: Steel Preparation
Construction Steel Preparation Steel should be cleaned and prepared by blast cleaning Sika Corporation
Slide 11: Armatec 1.65 Gal Unit A & B Components
Construction Armatec 110 1.65 Gal Unit A & B Comp. proportions are clearly marked on the side of the plastic jugs for easy mixing. Sika Corporation
Slide 12: Mixing
Construction Mixing Shake contents of A & B Components. For 3.5 Gal Unit: Pour entire amount of both A & B Component into a clean dry pail. For 1.65 Gal Unit: Proportion according to markings on side of jugs Sika Corporation
Slide 13: Mixing
Construction Mixing Mix liquid thoroughly for 30 seconds with a Sika paddle (jiffy mixer) on a low speed drill 400-600 rpm drill. Sika Corporation
Slide 14: Mixing
Construction Mixing Slowly add entire “C” Component while continuing to mix for 3 minutes until blend is uniform and free of lumps. Sika Corporation
Slide 15: Mixing
Construction Mixing While mixing for 3 minutes stop to scrape down the sides to insure all material is fully mixed Sika Corporation
Slide 16: Corrosion Protection Only: First Coat
Construction Corrosion Protection Only: Apply at 80 sq.ft./gal (20 mils). Take special care to properly coat the underside of the totally exposed steel. Allow Coating to dry 2-3 hours @ 73 degrees F. Sika Corporation
Slide 17: Corrosion Protection Only: Second Coat
Construction Corrosion Protection Only: Apply second coat at same coverage after waiting 2-3 hour for first coat to dry. Sika Corporation
Slide 18: Bonding Agent & Rebar Protection: First Coat
Bonding Agent & Rebar Construction Protection First Coat: Apply at 80 sq.ft./gal (20 mils). Take special care to properly coat the underside of the totally exposed steel. Allow Coating to dry 2-3 hours @ 73 degrees F. Sika Corporation
Slide 19: Bonding Agent & Rebar Protection: Second Coat
Bonding Agent & Rebar Construction Protection Second Coat: Apply at 80 sq.ft./gal (20 mils) on both steel and concrete substrate. Proceed to applying repair mortar “wet-on-wet”. If Armatec 110 is dry apply again prior to placing repair mortar. Sika Corporation
Slide 20: Sika Technical Data Sheets
Construction Sika Armatec 110 EpoCem Sika Technical Data Sheets can be obtained via www.sikaconstruction.com Refer to data sheets for specific information on each Sika product. Sika Corporation