Dentsply Sirona Inc. · NASDAQ:XRAY

Dentsply Sirona — Technical Presentation (May 2022)

32 slides from Dentsply Sirona's technical presentation, May 2022

  1. Slide 1: CEREC MTL Zirconia – Multi Transitional Layer Zirconia

    Peeee MIL™ Zirconia Multi Transitional Layer Zirconia

  2. Slide 2: Zirconia – Strong as ever. Beautiful like never before.

    Zirconia – Strong as ever. Beautiful like never before. CEREC MTL Zirconia is the solution that provides you with strong, precise restorations that are highly esthetic and natural looking: ▪ High Esthetics – natural multitransitional layer and high shade match. ▪ High Strength – greater than 850 MPa

  3. Slide 3: Natural Gradient for great Esthetics

    Natural Gradient for great Esthetics ▪ Due to its high translucency and high color matching characteristics, CEREC MTL Zirconia meets all esthetic needs. ▪ The excellent shade match with the most commonly used VITA classical shades enables for convenient color selection. ▪ Natural Gradient: due to t

  4. Slide 4: Strength for more Confidence

    Strength for more Confidence ▪ The high strength of > 850 MPa benefits both dentist and patient. Restorative treatment is even possible in areas with limited space. ▪ CEREC MTL Zirconia is indicated for: ▪ fully anatomical anterior and posterior crowns ▪ fully anatomical 3-unit anterior and posterio

  5. Slide 5: Fast Chairside Zirconia Workflow

    Fast Chairside Zirconia Workflow ▪ CEREC Primemill and CEREC SpeedFire for a fast CEREC MTL Zirconia workflow. With CEREC Primemill, excellent CEREC MTL With CEREC SpeedFire, a crown can be sintered Zirconia crowns can be milled in around 5 in 18 min2. The optional glaze firing will take 9 minutes i

  6. Slide 6: The Workflow of CEREC MTL Zirconia

    The Workflow of CEREC MTL Zirconia 6

  7. Slide 7: The Workflow

    The Workflow CEREC MTL Zirconia Design Mill Sinter Polish Glaze (optional) Cement 7

  8. Slide 8: Design

    Design Use CEREC SW 5.1.3 Material Pack or higher 8

  9. Slide 9: Compatible Milling machines

    Compatible Milling machines Milling Machines compatible with CEREC MTL Zirconia Machine SW Version Needed Processing Mode Dry/Wet CEREC Primemill CEREC SW 5.1.3. Material Pack Super Fast, Fast, Fine, Extra Fine Dry Super Fast (dry only), Fast, Fine, CEREC Primemill CEREC SW 5.2.2. or inLab CAM 22.0

  10. Slide 10: Milling Burs

    Milling Burs Prior to Milling, the right milling burs need to be installed: CEREC Primemill Burs for CEREC MC XL, CEREC MC X 10

  11. Slide 11: Mill

    Mill ▪ The data matrix code is printed on CEREC MTL Zirconia Blocks. The data matrix code contains information about the material, such as block size, color, batch number and the magnification factor of the block. The block scanner in the CEREC Primemill quickly scans the data matrix code on the blo

  12. Slide 12: Preparation for Sintering

    Preparation for Sintering ▪ The surfaces of the crown must be clean and ▪ After the milling process and prior to sintering, a dust-free before sintering. diamond or a tungsten carbide milling tool has ▪ Use the large dusting brush or compressed air to be used to remove the sprue prior to to thorough

  13. Slide 13: Sintering

    Sintering ▪ When sintering CEREC MTL Zirconia restorations in the CEREC SpeedFire, the CEREC software automatically transfers the job to the CEREC SpeedFire if the milling machine and the CEREC SpeedFire are connected. ▪ Place the restoration with the occlusal surface facing down directly on the top

  14. Slide 14: Sintering

    Sintering ▪ The furnace opens automatically following successful heat treatment. The process is not yet complete, as a cooling-off phase occurs in an open condition. There will be a signal tone once the cooling process has completed. When the unit’s LED status display is green, the furnace can be un

  15. Slide 15: Polishing

    Polishing ▪ CEREC MTL Zirconia can be finished by polishing or through a combination of polishing and glazing. ▪ Ensure the restoration is properly polished, including the occlusal surface, especially the areas that are in direct contact with the antagonist. ▪ After functional adjusting, re-polish t

  16. Slide 16: Preparing for Glazing (optional)

    Preparing for Glazing (optional) ▪ CEREC MTL Zirconia restorations can be glazed with: ▪ Dentsply Sirona Universal Stain and Glaze System or ▪ DS Universal Spray Glazes (with or without Fluo) ▪ Use the Glazing Support Single (for crowns) /Multi Unit (for bridges) holders and the CEREC SpeedPaste to

  17. Slide 17: Glazing (optional)

    Glazing (optional) DS Universal Stain and Glaze System DS Universal Spray Glazes (with or w/o Fluo) ▪ Apply a thin layer of the glaze material all over ▪ Prior to use, shake the spray can and then the crown surface by using a brush (e.g. Pinelo apply a uniform layer glaze to the surface of the by De

  18. Slide 18: Glazing (optional)

    Glazing (optional) Glazing CEREC MTL Zirconia in the CEREC SpeedFire ▪ Position the support with the restoration centrally on the top door insulation ▪ Select the “GLAZE” program on the CEREC SpeedFire control panel and allow the unit to cycle ▪ Glazing CEREC MTL Zirconia with other furnaces Pre-hea

  19. Slide 19: Cementation

    Cementation Cementation pre-treatment ▪ Prior to cementation of the crown, sandblast the internal surfaces in the one- way blasting process with maximum 50μm corundum (Aliuminiumoxide) at a pressure less than 2.5 bar. ▪ Do not touch the sandblasted surface Final Cementation ▪ For final cementation,

  20. Slide 20: Key Facts

    BUON ASUS A Ww oucw WONT, WLUW Daas Dentsply > Sirona “vu

  21. Slide 21: Key facts

    Key facts Fact CEREC MTL Zirconia # of shades available 7 shades available (A1, A2, A3, A3.5, B2, C2, D2) Sizes available mono (crowns, inlays, onlays & veneers) & medi (3-unit bridges) Dimensions mono bloc w: 19.2, h: 16.7, l: 20.2 Dimensions medi bloc w: 19.2, h: 16.7, l: 39.2 Type 4Y-TZP CTE (20-

  22. Slide 22: Competiton

    BUON ASUS A Ww oucw WONT, WLUW Daas Dentsply > Sirona “vu

  23. Slide 23: KATANA™ Zirconia Block (Kuraray Noritake)

    KATANA™ Zirconia Block (Kuraray Noritake) ▪ Indications: Crowns, bridges, veneers, inlays and onlays ▪ Strength: 763 MPa (3-Point) ▪ # of Layers: 4 Layers (Enamel Layer, Transition Layer 1 & 2, Body Layer) ▪ Minimal wall Thickness: ▪ Anterior crown: 0.8 mm ▪ Posterior crown: 1.0 mm ▪ Cross connector

  24. Slide 24: Chairside Zirconia (3M)

    Chairside Zirconia (3M) ▪ Indications: Crowns & bridges ▪ Strength: 1000 MPa (3-Point) ▪ # of Layers: Not a multilayer ▪ Minimal wall Thickness: ▪ Anterior & posterior crown: 0.8 mm ▪ Cross connector anterior: 12mm² ▪ Cross connector posterior: 14mm² ▪ Milling: Dry milling is recommended (Wet millin

  25. Slide 25: IPS e.max ZirCAD MT Multi (Ivoclar Vivadent)

    IPS e.max ZirCAD MT Multi (Ivoclar Vivadent) ▪ Indications: Crowns & bridges ▪ Strength: 850 MPa (biaxial!) ▪ # of Layers: 3 Layers (20% incisal zone, 20% transition zone, 60% dentin zone) ▪ Minimal wall Thickness: ▪ Anterior crown: 0.8mm ▪ Posterior crown: 1.0mm ▪ Cross connector anterior: 12mm² ▪

  26. Slide 26: Comparison

    Comparison KATANA™ Zirconia Block Chairside Zirconia IPS e.max ZirCAD MT Multi CEREC MTL Zirconia (Kuraray Noritake) (3M) (Ivoclar Vivadent) Crowns, bridges, veneers, inlays Crowns, bridges, veneers, inlays Indications Crowns, bridges Crowns, bridges and onlays and onlays Strength >850 MPa 763 MPa 1

  27. Slide 27: SKU Overview & Accessories

    SKU Overview & Accessories 27

  28. Slide 28: SKU Overview

    SKU Overview SKU CEREC MTL Zirconia mono (4 PC) SKU CEREC MTL Zirconia medi (2 PC) 5365450001 CEREC MTL Zirconia A1 mono 5365450021 CEREC MTL Zirconia A1 medi 5365450002 CEREC MTL Zirconia A2 mono 5365450022 CEREC MTL Zirconia A2 medi 5365450003 CEREC MTL Zirconia A3 mono 5365450023 CEREC MTL Zircon

  29. Slide 29: Accessories

    Accessories SKU Product Description 6580067 CEREC SpeedPaste 6611870 Glazing Support Single Unit +A 6583889 Glazing Support Multi Unit 5368273100 Dentsply Sirona Universal Spray Glaze Fluo 5368273101 Dentsply Sirona Universal Spray Glaze D605540 DS Universal Glaze D605542 DS Universal Glaze High Flu

  30. Slide 30: Burs for CEREC Primemill

    EC Primemill Burs for CEREC Primemill 67 13 940 Bur 2.5 ZrO, CS 67 13 932 Bur 1.0 CS 67 13 924 Bur 0.5 CS Tool Use Case Color Left Side Mill ZrO, Bur 2.5 ZrO, CS Extra Fine O Annies Bur 2.5 ZrO, CS @ = Burlocs Mill ZrO, Super-Fast Right Side Bur 1.0 CS Bur 0.5 CS Bur 2.5 ZrO, CS Bur 1.0 CS Possible

  31. Slide 31: Burs for CEREC MC XL, CEREC MC X

    Burs for CEREC MC XL, CEREC MC X 31

  32. Slide 32: CEREC – Dentsply Sirona 2020

    32 CEREC – Dentsply Sirona 2020

Dentsply Sirona — Technical Presentation (May 2022) on 6ix