Slide 1: 2020 Ford Ignition and Door Pinning Instructions 2019-2020
2020 FORD IGNITION AND DOOR PINNING INSTRUCTIONS 2019 -2020 INTERNAL 2 TRACK ESCAPE/LINCOLN CORSAIR(MKC) 106 Groove WITTE • STRATTEC • ADAC VEHICLE ACCESS SYSTEMS TECHNOLOGY
Slide 2: Ford 2 Track Key Code Series
2020 Ford FORD 2 TRACK KEY CODE SERIES Ford North America programs Model Year 2020 CX482 (Escape) & CX483 (MKC/Corsair) Codes Series 30001-31544 WITTE • STRATTEC • ADAC VEHICLE ACCESS SYSTEMS TECHNOLOGY
Slide 3: Ford 2 Track Key Depth and Spacing
2020 Ford FORD 2 TRACK KEY DEPTH AND SPACING WITTE • STRATTEC • ADAC VEHICLE ACCESS SYSTEMS TECHNOLOGY
Slide 4: Ford 2 Track Cut Key Reading
2020 Ford FORD 2 TRACK CUT KEY READING Key found in ignition education Chart A pack Key Reading by Cuts Part Number - 7039965 1) Start with the key bow to the left and the tip of the key pointing to the right 2) Observe the cuts on the upper or primary half of the key 3) A cut nearest the centerline
Slide 5: Ford 2 Track Pinning - Ignition
2020 Ford FORD 2 TRACK PINNING - IGNITION Key reading procedure 1. Determine the matching key cut depth at each station 2. Using the cut key, measure the key cut depth at each station (refer to figure 1) and write down the corresponding key cut depths in terms of depth code, not the actual measure
Slide 6: Ford 2 Track Pinning - Ignition
2020 FORD FORD 2 TRACK PINNING - IGNITION Ignition Stations Use Stations 2 – 10 Only Eng Code 2087X Tip Bow Centerline 4 3 3 1 2 4 4 2 3 WITTE • STRATTEC • ADAC VEHICLE ACCESS SYSTEMS TECHNOLOGY
Slide 7: Ford 2 Track Pinning - Ignition: Tumbler Identification and Pinning
2020 Ford FORD 2 TRACK PINNING - IGNITION Tumbler Identification and Pinning *Tumbler bags marked as follows: 1L - 4231964 – not used 1R – 4231969 – 1 total 2L - 4231965 – not used 2R – 4231970 – 2 total 3L - 4231966 – not used 3R – 4231971 – 3 total 4L - 4231967 – 1 total 4R – 4231972 – 2 total 5L
Slide 8: Ford 2 Track Pinning - Cylinder Orientation and Tumbler Placement
2020 Ford FORD 2 TRACK PINNING - IGNITION Cylinder Orientation and tumbler placement 3. Select the required tumblers according to the key cut depths. (refer to figure 2) 4. Insert the required tumblers into the tumbler slots (top-side) in the proper orientation (refer to figure 3) WITTE • STRATTEC
Slide 9: Ford 2 Track Pinning - Cylinder Orientation and Tumbler Placement
2020 Ford FORD 2 TRACK PINNING - IGNITION Cylinder Orientation and tumbler placement 5. While holding down the tumblers, turn the cylinder and repeat steps 4 and 5 for the bottom side. (refer to figure 4) WITTE • STRATTEC • ADAC VEHICLE ACCESS SYSTEMS TECHNOLOGY
Slide 10: Ford 2 Track Pinning - Assembly
2020 Ford FORD 2 TRACK PINNING - IGNITION Assembly 6. Insert the key into the keyhole and verify that all installed tumblers are flush with the cylinder exterior surface(refer to figure 5). Do not pull the key out. If you do, the tumblers will fall out as they are not snap in or self retaining. 7.
Slide 11: Ford 2 Track Pinning - Assembly
2020 Ford FORD 2 TRACK PINNING - IGNITION Assembly 9. Slide the tumbled and greased cylinder in side the sleeve 10. Hold the back part of the cylinder and carefully remove the key (refer to figure 6). Cylinder cannot be removed from housing at this point, if this occurs, the tumblers will fall out