DuPont de Nemours, Inc. · NYSE:DD
DuPont de Nemours — DuPont — Technical Presentation (May 2011)
16 slides from DuPont de Nemours's technical presentation, May 2011
Slide 1: Material Solutions – Turbo, EGR System
1 Material Solutions – Turbo, EGR System m & anc l st ca e si mi re Re h e tu C ra pe Te
Slide 2: TC System – With Recycle Streams Highlighted
2 TC System – With Recycle Streams Highlighted Intercooler Exhaust Fresh Air Inlet manifold EGR system PCV system Air filter Exhaust manifold Turbo charger
Slide 3: Approximate Heat Rating of Elastomers, Fibers and Plastics
OPIS JOH 2PIS PIOD 3 Approximate Heat Rating of Elastomers, Fibers and Plastics FKM — Viton® Meta-aramid VMQ - Silicone Nomex® PPA Zytel® HTN Zytel® Plus PA66 Zytel® PA6 Zytel® 175 AEM-HT - Vamac® 160 AEM — Vamac® 150 Polyester TPC-ET Hytrel® 12 Oo TPV EPDM/PP 6 QO A l = 0) {e) no] x (0) > i) ; 0 El
Slide 4: Chemical Cocktail Resistance
4 Chemical Cocktail Resistance Previous Automotive Requirements for TC Materials • Hot Air – good heat resistance required • Oil resistance required Requirement Changes as Result of Recycle Streams • Fuel and Oil from PCV system • Acid condensate from EGR and PCV system Laboratory Testing Parameters
Slide 5: Acid Condensate – CPE
5 Acid Condensate – CPE Tested: 1 week at 90°C in acid condensate from European OEM • pH of about 3 • based on organic acids Tensile bar at end of test. Could not run physicals.
Slide 6: FKM and ECO in Acid Condensate
6 FKM and ECO in Acid Condensate Tested 1 week at 90°C in Viton® GF-200S ECO ‘poor acid condensate from ‘good samples ’ samples’ European OEM • pH of about 3 • based on mineral acids Picture of a VI sample at end of test. ECO sample had large increase in VI.
Slide 7: HNBR samples in low pH acid condensate
7 HNBR samples in low pH acid condensate Tested – 1 week at 100°C in acid condensate • pH of about 1 • based on blend of organic and mineral acids Picture of a tensile bar at end of test. Could not test sample. In same test an AEM sample performed well.
Slide 8: Resistance to Acid Condensate, Engine Oils for Elastomers
Resistance to Acid Condensate, Engine Oils for Elastomers t FKM Viton®\ Good Oil Resistance With Metal Oxides With low levels of fuel CPE and ECO ‘ Poor Acid Condensate Resistance Assumes newer engine oils: more synthetic with aggressive additive package. Elastomers with poor oil resistance, e.g. EP
Slide 9: Flexible Plastics – Hytrel, Flexible Zytel: EGR Exposure
9 Flexible Plastics – Hytrel®, Flexible Zytel®: EGR Exposure EGR liquid contact, 2000h @ 80°C
Slide 10: Rigid Plastics – Zytel Grades - EGR Exposure
10 Rigid Plastics – Zytel® Grades - EGR Exposure Reinforced materials, EGR simulation 80°C ZY 70G30HSLR BK099 200 ZY 70G35HSLRA4 BK267 Tensile strength [MPa] ZY 70G35HSLX BK357 150 ZY BM70G15HSLR BK357 ZY BM70G20HSLX BK357 100 ZY 73G30HSL BK416 ZY BM73G15THS BK317 50 ZY HTN54G35HSLR BK031 0 0 500 10
Slide 11: Material Solutions – Turbo, EGR System
11 Material Solutions – Turbo, EGR System In te gr a tio n
Slide 12: Air Induction – Design Requirements
12 Air Induction – Design Requirements Chemical Resistance (Acid, pH, fuel, oil) 1 0.8 Excellent 0.6 Good Need to Assembly Rigid 0.4 150 200 Temp, °C balance 0.2 Poor 23 -40 many Flexible 0 different minus 68 1000 factors 1 3000 5000 plus Engine Time, hours Movement 2 3 Pressure, bar
Slide 13: Air ducts - Design Options
13 Air ducts - Design Options Injection molded Welded shells 1 + rubber hoses* Blow molded 2 + rubber hoses* 3 Full integration -- All plastic or rubber * DuPont products for rubber hoses : Vamac ® , Viton ®, Nomex ®, Kevlar ®
Slide 14: Typical Elastomeric Hose Constructions
14 Typical Elastomeric Hose Constructions Up to 135°C • EPDM or ECO and Kevlar® Up to 160°C • AEM Vamac® and Kevlar®. Up to 180°C • AEM Vamac® Ultra HT and Nomex® Above 180°C • VMQ silicone rubber with Fiber – Burst strength & heat resistance Nomex® Elastomer – Chemical & heat • FKM Viton® used as i
Slide 15: TC System – With Air Ducts and Hoses Highlighted
15 TC System – With Air Ducts and Hoses Highlighted Intercooler Exhaust Fresh Air Inlet manifold EGR system PCV system Air filter Exhaust manifold Turbo charger
Slide 16: Contacts
16 Steven Mok Ed McBride Thermal Systems Technology Leader 248-459-5380 (302) 999-2153 steven.mok@usa.dupont.com Edward.McBride@usa.dupont.com Randy White Volker Plehn Air Delivery Systems Kalrez® & Vespel® 315-597-0099 1-248-583-7921 Randal.B.White@usa.dupont.com volker.Plehn@usa.dupont.com John Hu